Products

3-(4-Methylbenzylidene)camphor

Item number	677561
CAS	36861-47-9
Formula	C18H22O
Molecular weight	254,37 g/mol
Quantity	1X250MG
storage conditions	20 °C
CoA / MSDS	Retrieve CoA Retrieve MSDS

Price

Please log in.

Product Variations:

Product		Catalog No./ CAS No.	Quantity	Price
3-(4-Methylbenzylidene)camphor		677561 36861-47-9	1X250MG	Please log in.

Safety Data Sheet	according to Regulation (EC) No 1907/2006 (REACH) Classifications according to Regulation (EC) No 1272/2008. Printdate 15.11.2024
IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
Product name:	3-(4-Methylbenzylidene)camphor
Catalog No.:	677561
Relevant identified uses of the substance or mixture	Identified: Laboratory chemical uses: R&D
Uses advised against:	HPC Standards GmbH Am Wieseneck 7 04451 Cunnersdorf Deutschland Tel. +49 34291 3372-36 Fax. +49 34291 3372-39 contact@hpc-standards.com
Emergency telephone number	HPC Standards Tel. +49 34291 3372-36 This number is only available during office hours.
HAZARDS IDENTIFICATION	Classification of the substance or mixture Classification according to Regulation (EC) No 1272/2008 Reproductive toxicity (Category 2), H361
Label elements
Pictogram	GHS08 silhouete silhouete
	Signal word Warning Hazard statement(s) H361 Suspected of damaging fertility or the unborn child. Precautionary statement(s) P281 Use personal protective equipment as required. Supplemental Hazard Statements none 2.3 Other hazards This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
COMPOSITION/INFORMATION ON INGREDIENTS	3.1 Substances Molecular weight : 254,37 g/mol CAS-No. : 36861-47-9 EC-No. : 253-242-6 Hazardous ingredients according to Regulation (EC) No 1272/2008 Component Classification Concentration 3-(4-Methylbenzylidene)camphor CAS-No. 36861-47-9 EC-No. 253-242-6 Repr. 2; H361 <= 100 %
Formula	C18H22O
Molecular Weight (g/mol)	254.37
CAS-No.	36861-47-9
FIRST AID MEASURES	4.1 Description of first aid measures General advice Consult a physician. Show this safety data sheet to the doctor in attendance. If inhaled If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician. In case of skin contact Wash off with soap and plenty of water. Consult a physician. In case of eye contact Flush eyes with water as a precaution. If swallowed Never give anything by mouth to an unconscious person. Rinse mouth with water. Consult a physician. 4.2 Most important symptoms and effects, both acute and delayed The most important known symptoms and effects are described in the labelling (see section 2.2) and/or in section 11 4.3 Indication of any immediate medical attention and special treatment needed No data available
FIRE-FIGHTING MEASURES	5.1 Extinguishing media Suitable extinguishing media Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide. 5.2 Special hazards arising from the substance or mixture Carbon oxides 5.3 Advice for firefighters Wear self-contained breathing apparatus for firefighting if necessary. 5.4 Further information No data available
ACCIDENTAL RELEASE MEASURES	6.1 Personal precautions, protective equipment and emergency procedures Use personal protective equipment. Avoid dust formation. Avoid breathing vapours, mist or gas. Ensure adequate ventilation. Evacuate personnel to safe areas. Avoid breathing dust. For personal protection see section 8. 6.2 Environmental precautions Prevent further leakage or spillage if safe to do so. Do not let product enter drains. 6.3 Methods and materials for containment and cleaning up Pick up and arrange disposal without creating dust. Sweep up and shovel. Keep in suitable, closed containers for disposal. 6.4 Reference to other sections For disposal see section 13.
HANDLING AND STORAGE	7.1 Precautions for safe handling Avoid contact with skin and eyes. Avoid formation of dust and aerosols. Provide appropriate exhaust ventilation at places where dust is formed. Normal measures for preventive fire protection. For precautions see section 2.2. 7.2 Conditions for safe storage, including any incompatibilities Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Storage class (TRGS 510): 13: Non Combustible Solids 7.3 Specific end use(s) Apart from the uses mentioned in section 1.2 no other specific uses are stipulated
EXPOSURE CONTROLS/PERSONAL PROTECTION	8.1 Control parameters 8.2 Exposure controls Appropriate engineering controls Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday. Personal protective equipment Eye/face protection Safety glasses with side-shields conforming to EN166 Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Skin protection Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching gloves outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands. The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it. Full contact Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: 480 min Material tested:Dermatril® Splash contact Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: 480 min Material tested:Dermatril® data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 87300, e-mail sales@kcl.de, test method: EN374 If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the CE approved gloves. This recommendation is advisory only and must be evaluated by an industrial hygienist and safety officer familiar with the specific situation of anticipated use by our customers. It should not be construed as offering an approval for any specific use scenario. Body Protection Impervious clothing, The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace. Respiratory protection Where risk assessment shows air-purifying respirators are appropriate use a full-face particle respirator type N100 (US) or type P3 (EN 143) respirator cartridges as a backup to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air respirator. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU). Control of environmental exposure Prevent further leakage or spillage if safe to do so. Do not let product enter drains.
PHYSICAL AND CHEMICAL PROPERTIES	9.1 Information on basic physical and chemical properties a) Appearance Form: crystalline Colour: white b) Odour No data available c) Odour Threshold No data available d) pH No data available e) Melting point/freezing point No data available f) Initial boiling point and boiling range No data available g) Flash point No data available h) Evaporation rate No data available i) Flammability (solid, gas) No data available j) Upper/lower flammability or explosive limits No data available k) Vapour pressure No data available l) Vapour density No data available m) Relative density No data available n) Water solubility No data available o) Partition coefficient: noctanol/water No data available p) Auto-ignition temperature No data available q) Decomposition temperature No data available r) Viscosity No data available s) Explosive properties No data available t) Oxidizing properties No data available 9.2 Other safety information No data available
STABILITY AND REACTIVITY	10.1 Reactivity No data available 10.2 Chemical stability Stable under recommended storage conditions. 10.3 Possibility of hazardous reactions No data available 10.4 Conditions to avoid No data available 10.5 Incompatible materials Strong oxidizing agents 10.6 Hazardous decomposition products Hazardous decomposition products formed under fire conditions. - Carbon oxides Other decomposition products - No data available In the event of fire: see section 5
TOXICOLOGICAL INFORMATION	11.1 Information on toxicological effects Acute toxicity LD50 Oral - Rat - > 5.000 mg/kg (OECD Test Guideline 401) LD50 Dermal Dermal - Rat - > 2.000 mg/kg (OECD Test Guideline 402) Skin corrosion/irritation Skin - Rabbit Result: No skin irritation Remarks: (own results) Skin - Human Result: No skin irritation Remarks: (own results) Serious eye damage/eye irritation Eyes - In vitro study Result: No eye irritation (Hens egg-membrane test for irritation (HET-CAM)) Eyes - Rabbit Result: No eye irritation Remarks: (own results) Respiratory or skin sensitisation - Guinea pig Result: negative Remarks: (own results) - Human Result: negative Remarks: (own results) Germ cell mutagenicity Ames test Result: negative Mutagenicity (mammal cell test): chromosome aberration. Result: negative Carcinogenicity IARC: No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC. Reproductive toxicity Specific target organ toxicity - single exposure Specific target organ toxicity - repeated exposure Aspiration hazard Additional Information RTECS: DT5099565 Hazardous properties cannot be excluded but are unlikely when the product is handled appropriately. Handle in accordance with good industrial hygiene and safety practice.
ECOLOGICAL INFORMATION	12.1 Toxicity Toxicity to daphnia and other aquatic invertebrates Immobilization EC50 - Daphnia magna (Water flea) - < 0,86 mg/l - 48 h(3-(4- Methylbenzylidene)camphor) (OECD Test Guideline 202) Toxicity to bacteria EC50 - activated sludge - > 10.000 mg/l - 3 h(3-(4- Methylbenzylidene)camphor) (OECD Test Guideline 209) 12.2 Persistence and degradability Biodegradability Result: - Not readily biodegradable. (MITI test) Result: - Not readily biodegradable. (OECD Test Guideline 301F) Result: - Not readily biodegradable. (OECD Test Guideline 301D) Biochemical Oxygen Demand (BOD) < 10 mg/g(3-(4-Methylbenzylidene)camphor) 12.3 Bioaccumulative potential 12.4 Mobility in soil 12.5 Results of PBT and vPvB assessment This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher. 12.6 Other adverse effects Additional ecological information
DISPOSAL CONSIDERATIONS	13.1 Waste treatment methods Product Offer surplus and non-recyclable solutions to a licensed disposal company. Contact a licensed professional waste disposal service to dispose of this material. Dissolve or mix the material with a combustible solvent and burn in a chemical incinerator equipped with an afterburner and scrubber. Contaminated packaging Dispose of as unused product.
TRANSPORT INFORMATION	14.1 UN number ADR/RID: - IMDG: - IATA: - 14.2 UN proper shipping name ADR/RID: Not dangerous goods IMDG: Not dangerous goods IATA: Not dangerous goods 14.3 Transport hazard class(es) ADR/RID: - IMDG: - IATA: - 14.4 Packaging group ADR/RID: - IMDG: - IATA: - 14.5 Environmental hazards ADR/RID: no IMDG Marine pollutant: no IATA: no 14.6 Special precautions for user No data available
REGULATORY INFORMATION	15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture This safety datasheet complies with the requirements of Regulation (EC) No. 1907/2006. 15.2 Chemical safety assessment For this product a chemical safety assessment was not carried out
OTHER INFORMATION	The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. For lab use only!